Black Friday Flash Sale - Everything Must Go at 75% Off - Ends in 0d 00h 00m 00s - Coupon code: w75best

Cisco 300-120 Dumps

Page: 1 / 11
Total 105 questions

Implementing Cisco Wireless Advanced Solutions (300-120 WLSI) v1.2 Questions and Answers

Question 1

A network engineer recently deployed Cisco Catalyst Center (formerly DNA Center) to a customer site. The customer is being flooded with alarms for wireless clients that fail AAA authentication. What is the path to disable the alarm in the Cisco Catalyst Center user interface?

Options:

A.

Assurance > Manage > Sensors

B.

Assurance > Manage > Intelligent Capture Settings

C.

Assurance > Manage > Issue Settings

D.

Assurance > Manage > Health Score Settings

Question 2

Refer to the exhibit.

A network architect configured the Cisco Catalyst 9800 Series Controller to find out information on client types in the wireless network. RADIUS profiling is enabled so that the controller forwards the information about clients to a Cisco ISE server through vendor-specific RADIUS attributes. The ISE server is not profiling any data from the controller. Which configuration must be added in the blank in the code to accomplish the profiling on the Cisco 9800 Series controller?

as

Options:

A.

aaa accounting identity acct_method start-stop group rad-group

B.

aaa accounting network acct_method start-stop group rad-group

C.

aaa accounting exec acct_method start-stop group rad-group

D.

aaa accounting commands acct_method start-stop group rad-group

Question 3

An engineer is setting up a new unique NAD on a Cisco ISE.

Which two parameters must be configured? (Choose two.)

Options:

A.

device host name

B.

device password

C.

RADIUS fallback

D.

device IP address

E.

RADIUS shared secret

Question 4

A customer has a distributed wireless deployment model where the WLCs are located in the data centers. Because the file servers are located in the data center, the traffic from the corporate WLAN “Corp-401266017” must go through the controllers, where the guest WLAN “Guest-19283746” traffic must use the local Internet line installed in each office. Which configuration will accomplish this task?

Options:

A.

Disable Local Switching for the corporate and guest WLAN.

B.

Disable Local Switching for the corporate WLAN and enable it for the guest WLAN.

C.

Enable Local Switching for the corporate and guest WLAN.

D.

Enable Local Switching for the corporate WLAN and disable it for the guest WLAN.

Question 5

An engineer must implement Cisco Identity-Based Networking Services at a remote site using ISE to dynamically assign groups of users to specific IP subnets. If the subnet assigned to a client is available at the remote site, then traffic must be offloaded locally, and subnets are unavailable at the remote site must be tunneled back to the WLC. Which feature meets these requirements?

Options:

A.

learn client IP address

B.

FlexConnect local authentication

C.

VLAN-based central switching

D.

central DHCP processing

Question 6

A network engineer observes a spike in controller CPU overhead and overall network utilization after multicast is enabled on a controller with 500 APs. Which feature corrects the issue?

Options:

A.

controller IGMP snooping

B.

multicast AP multicast mode

C.

broadcast forwarding

D.

unicast AP multicast mode

Question 7

An engineer configures Cisco CMX. which uses Layer 2 high availability on primary and secondary CMX instances, according to these specifications:

· Primary CMX IP address: 192.168.1.4/24

· Secondary CMX IP address 192 168.4.4/24

· Virtual IP address: 192.168.4.1/24

in testing, the engineer discovers that the failover fails. Which action resolves the issue?

Options:

A.

Place the primary CMX IP address and the virtual IP address in the same subnet

B.

Use a virtual IP address with CMX Layer 3 high availability

C.

Place the primary CMX IP address and the secondary CMX IP address in the same subnet.

D.

Place the primary CMX IP address and the secondary CMX IP address in the same subnet

Question 8

An engineer is defining a new Cisco AVC profile with different rules for HR and VIP users. Both user types connect to a single SSID and authenticate by using their Active Directory credentials via Cisco ISE. The engineer wants to apply the AVC profile dynamically to the user types.

Which Cisco AV pair attribute must be applied to Cisco ISE?

Options:

A.

policy-avc-role

B.

policy-role-avc

C.

avc-profile-name

D.

role-name-avc

Question 9

A customer configures iPSK for use with a Cisco Catalyst 9800 Series controller. The configuration is complete, but the wireless client fails to authenticate to the network. Which implementation resolves this issue?

Options:

A.

Enable iPSK on the WLAN.

B.

Configure the DHCP Required option on the policy profile.

C.

Configure an accounting list on the policy profile.

D.

Enable the AAA Override option on the policy profile.

Question 10

A retail chain is deploying a wireless network across multiple branch stores using Cisco Catalyst 9800 Series controllers and access points in FlexConnect mode. The employee WLAN uses WPA2-PSK and must remain available during WAN outages while still being centrally managed when WAN connectivity is available.

Which two actions should the network administrator implement to support this design? (Choose two.)

Options:

A.

Centralize all authentication at the controller and rely on cached credentials at the APs during outages.

B.

Configure the controller to centrally switch the employee WLAN traffic at all times.

C.

Install a local RADIUS server at each branch to authenticate WPA2-PSK users.

D.

Group the FlexConnect APs by branch in a FlexConnect group so branch-specific settings can be applied.

E.

Configure the FlexConnect APs to locally switch the employee WLAN traffic.

Question 11

For security purposes, an engineer enables CPU ACL and chooses an ACL on the Security > Access Control Lists > CPU Access Control Lists menu. Which kind of traffic does this change apply to as soon as the change is made?

Options:

A.

wireless traffic only

B.

wired traffic only

C.

VPN traffic

D.

wireless and wired traffic

Question 12

A network engineer wants to implement QoS across the network that supports multiple VLANs. All the APs are connected to switch ports and are configured in local mode. Which trust model must be configured on the switch ports to which the APs are connected?

Options:

A.

CoS

B.

WMM UP

C.

DSCP

D.

IPP

Question 13

A customer has Cisco FlexConnect APs at all remote branches and requires zero downtime through the FlexConnect Fault Tolerance feature. Which two configurations must be identical on both controllers to maintain connectivity when the APs switch from the primary WLC to the backup WLC because of a WAN failure? (Choose two.)

Options:

A.

AAA server ordering

B.

mobility domain

C.

interface configuration

D.

WLAN ordering

E.

AP join profile

Question 14

An engineer must implement intrusion protection on the WLAN. The AP coverage is adequate and on-channel attacks are the primary concern. The building is historic, which makes adding APs difficult. Which AP mode and submode must be implemented?

Options:

A.

AP mode: local, AP submode: none

B.

AP mode: monitor, AP submode: WIPS

C.

AP mode: monitor, AP submode: none

D.

AP mode: local, AP submode: WIPS

Question 15

A wireless network uses Cisco ISE to implement 802 1x for user authentication and an Active Directory server as a user database After a power outage, the wireless clients cannot connect to the wireless network The ISE log reports a "clock skew" Which action addresses this issue?

Options:

A.

Enter the correct credentials

B.

Restart the ISE service

C.

Install a trusted certificate

D.

Configure NTP

Question 16

An engineer configures custom QoS mapping on a Cisco Catalyst 9800 Series Wireless Controller. The engineer uses the Cisco-recommended configuration for DSCP-to-UP mapping. Which two wired-to-wireless QoS mappings should be configured? (Choose two.)

Options:

A.

DSCP CS4 to 802.11e UP 4

B.

DSCP EF to 802.11e UP 7

C.

DSCP CS3 to 802.11e UP 3

D.

DSCP EF to 802.11e UP 6

E.

DSCP CS4 to 802.11e UP 5

Question 17

Which three properties are used for client profiling of wireless clients? (Choose three.)

Options:

A.

HTTP user agent

B.

DHCP

C.

MAC OUI

D.

hostname

E.

OS version

F.

IP address

Question 18

A network engineer created a new wireless network that will be used for guest access. The corporate network must utilize all rates. The guest network must use only lower rates instead of 802.11n data rates. To what must the WMM policy of the WLAN be set to accomplish this task?

Options:

A.

required

B.

allowed

C.

disabled

D.

mandatory

Question 19

What must be configured on the Global Configuration page of the WLC for an AP to use 802.1x to authenticate to the wired infrastructure?

Options:

A.

local access point credentials

B.

RADIUS shared secret

C.

TACACS server IP address

D.

supplicant credentials

Question 20

An engineer is configuring location services within Cisco Spaces (formerly Cisco DNA Spaces). The solution must track interfering devices. Which component of Cisco Spaces must be configured?

Options:

A.

Proximity Reporting

B.

Detect and Locate

C.

Cisco DNA Spaces SDK

D.

Location Analytics

Question 21

Company XYZ recently migrated from AireOS to IOS XE 9800 WLCs. The Internet bandwidth must be limited to 5 Mbps for each guest client as per the global standard. In which configuration on the Cisco Catalyst 9800 WLC must the QoS requirement be added?

Options:

A.

table map

B.

policy map

C.

service policy

D.

class map

Question 22

On a Cisco Catalyst 9800 Series Wireless Controller, an engineer wants to prevent a FlexConnect AP from allowing wireless clients to connect when its Ethernet connection is nonoperational. Which command set prevents this connection?

Options:

A.

config terminal

wireless flexconnect profile [profile name]

ethernet-fallback-enable

end

B.

config terminal

wireless flexconnect profile [profile name]

fallback-radio-shut

end

C.

config terminal

wireless profile flex [profile name]

fallback-radio-shut

end

D.

config terminal

wireless profile flex [profile name]

ethernet-fallback-enable

end

Question 23

An engineer configured a single WLAN with WPA2-Enterprise and wants to use Cisco ISE to apply AVC profiles to users in different departments. After users successfully authenticate to the wireless network, each department is placed in a unique VLAN and assigned an AVC profile. Which feature must be enabled on the Cisco WLC?

Options:

A.

Role-based access control

B.

Change of Authorization

C.

Local Profiling

D.

AAA Override

Question 24

Company XYZ recently migrated from legacy WLCs to Cisco Catalyst 9800 WLCs. According to the global standard, Internet bandwidth must be limited to 5 Mbps for each guest client. To which Cisco Catalyst 9800 WLC configuration component must the QoS requirement be added?

Options:

A.

table map

B.

service policy

C.

class map

D.

policy map

Question 25

A network engineer needs to configure multicast in the network. The implementation will use multiple multicast groups and PIM routers. Which address provides automatic discovery of the best RP for each multicast group?

Options:

A.

224.0.0.13

B.

224.0.0.14

C.

224.0.1.39

D.

224.0.1.40

Question 26

Refer to the exhibit. A university network administrator notices that wireless guest users consume a significant amount of uplink internet bandwidth in the library, which causes throughput issues on staff SSID. To throttle this bandwidth use, the administrator intends to configure a QoS policy for guests that:

Which class-map configuration must the administrator implement?

as

as

as

Options:

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Question 27

Exhibit:

as

Refer to the exhibit.

A wireless network engineer has been tasked with implementing AVC in a FlexConnect locally switched network. The AVC feature is properly configured for the WLAN named WLSI-AAA and the policy profile f2602. However, the AVC statistics are not displayed for this WLAN.

Which configuration change should be implemented to display the AVC statistics for this WLAN?

Options:

A.

Configure policy profile C2602 to use a different AVC policy.

B.

Configure policy profile f2602 to use a different flow monitor.

C.

Configure policy profile C2602 to use local switching for client data.

D.

Configure policy profile f2602 to use the same interface as C2602.

Question 28

Where is Cisco Hyperlocation enabled on a Cisco Catalyst 9800 Series Wireless Controller web interface?

Options:

A.

Policy Profile

B.

AP Join Profile

C.

Flex Profile

D.

RF Profile

Question 29

Refer to the exhibit.

An engineer tries to manage the rogues on the Cisco WLC. Based on the configuration, which AP is marked as malicious by the controller?

as

Options:

A.

rogue AP with SSID admin seen for 4000 seconds and heard at -70dBm

B.

rogue AP with SSID admin seen for 3000 seconds and heard at -60dBm

C.

rogue AP with SSID admin seen for 4000 seconds and heard at -60dBm

D.

rogue AP with SSID admin seen for 3000 seconds and heard at -70dBm

Question 30

What is the difference between PIM sparse mode and PIM dense mode?

Options:

A.

Sparse mode supports only one switch. Dense mode supports multiswitch networks.

B.

Sparse mode floods. Dense mode uses distribution trees.

C.

Sparse mode uses distribution trees. Dense mode floods.

D.

Sparse mode supports multiswitch networks. Dense mode supports only one switch.

Question 31

An engineer is configuring multicast for two WLCs. The controllers are in different physical locations and each handles around 500 wireless clients. How should the CAPWAP multicast group address be assigned during configuration?

Options:

A.

Each WLC must be assigned a unique multicast group address.

B.

Each WLC management address must be in the same multicast group.

C.

Both WLCs must be assigned the same multicast group address.

D.

Each WLC management address must be in a different multicast group.

Page: 1 / 11
Total 105 questions