Huawei H20-923_V1.0 Dumps

Wizard startup commissioning is designed to verify that the unit’skey controllable subsystemscan be started, regulated, and protected correctly. Conditions that prevent a subsystem from operating normally will directly cause commissioning failure. If thecondensate pump is stuck, the drainage function cannot be validated and water may accumulate in the drain pan, which is treated as a functional fault during commissioning. Ifindoor fan 2 drive is faulty, the fan system cannot meet airflow requirements or redundancy expectations, so the fan commissioning item fails. If theelectronic expansion valve (EEV) is not opened, refrigerant flow and cooling control cannot be established, so the cooling system commissioning fails because the unit cannot build a stable refrigeration cycle or reach expected operating parameters.

In contrast, thewater leakage ropeis aprotective detection accessoryused for leak sensing and alarming. While it is important for site safety and recommended for operation, its absence typically does not block the unit from completing the functional commissioning steps for fans, cooling, and drainage; it mainly affects leak detection coverage and related alarms rather than the basic startup commissioning pass/fail.

In Huawei smart module management (such as on the ECC800-Pro/WebUI),Device Managementis used to centrally view and maintain managed objects (UPS, SmartLi, rPDU, sensors, air conditioners, etc.). TheOverviewpage provides a consolidated snapshot of a device’s operating status, key parameters, running mode, and basic identification information so engineers can quickly judge whether the device is healthy and online. TheAlarmview lists active and historical alarms related to the device, supporting rapid fault isolation and verification after recovery. TheSignalview shows monitoring points and I/O status (including analog values and digital inputs/outputs where applicable), which helps engineers confirm sensor wiring, linkage logic, and real-time state changes during commissioning and troubleshooting. TheService periodinformation is used for lifecycle and maintenance planning, such as tracking service time, maintenance intervals, or component life indicators where supported, enabling preventive maintenance and reducing unexpected downtime. Therefore, Device Management supports viewing all four categories.

For the Huawei UPS5000-H, inverter startup is executed through theUPS’s own control interfaces, which provide the “Running Control / Inv. ON” operation with the required confirmations and permissions. TheUPS LCD (MDU touchscreen)supports inverter startup through menu operations such as selecting inverter start functions and confirming the action after authentication. TheUPS WebUIalso provides the same operational control path, where an operator logs in and issues theInv. ONcommand under the UPS monitoring/running control pages. These two interfaces are part of the UPS monitoring and control design and are explicitly used for commissioning and routine O&M actions.

By contrast,ECC(data center controller) andNetEco(management platform) are mainly used for site-level monitoring, alarm collection, visualization, reporting, and centralized management. While they can display UPS status and alarms (and may integrate with UPS data), inverter startup is defined as aUPS running control operationperformed on the UPS’s LCD or WebUI control plane to ensure proper authorization, safety checks, and command traceability.

In Huawei NetEco statistical reporting, the query range is constrained by the report data retention policy and how summary data is stored. Forhourly statistics, the platform keeps a limited window of high-granularity data to balance storage consumption and performance. The hourly report retention is120 hours, which equals5 days. That is why hourly statistics queries are limited to5 days—beyond that window, hourly granularity is no longer retained in the report database for direct querying. For longer time horizons, NetEco relies on lower-granularity summaries (daily/weekly/monthly/yearly). Formonthly statistics, the platform supports long-term trend analysis and KPI tracking, and the maximum historical horizon aligns with the long-term statistics retention boundary used by NetEco reporting, which isup to 5 years. This design ensures fast query response, manageable database growth, and clear separation between short-term operational detail (hourly) and long-term management analysis (monthly/yearly).

Huawei facility O&M methods emphasize using monitored operating data to locate inefficiencies before they become faults. Airflow-related cooling inefficiency commonly appears as hot spots at rack inlets, elevated return air temperature fluctuations, abnormal fan speed increases, or uneven temperature distribution across aisles. By trending rack inlet temperature sensors alongside cooling unit supply/return temperatures and fan speed or airflow commands, operations teams can distinguish between insufficient cooling capacity and poor airflow organization. Recirculation (hot air returning to rack inlets) often raises localized inlet temperatures without a proportional rise in room average temperature, while bypass (cold air short-circuiting back to returns) reduces cooling effectiveness and can drive fans to higher speeds unnecessarily. Data-driven checks support targeted corrective actions such as sealing cable openings, adjusting floor tile placement, restoring containment integrity, balancing airflow, or optimizing setpoints. This approach improves thermal stability, prevents overcooling, reduces energy waste, and aligns with Huawei’s emphasis on integrated monitoring and closed-loop optimization for reliable, efficient operation.

For onsite replacement of a UPS power module, Huawei’s maintenance logic follows a safe “isolate → remove → insert → re-enable” sequence controlled by the moduleready switch. During removal, the ready switch must be rotated to theOFFstate first so the module is logically isolated from operation and will not participate in power conversion. After isolation, the four fixing screws are removed and a short waiting period is required to allow internal energy in capacitors to discharge before the module is pulled out. This matches statement②. During installation, the ready switch must remainOFFbefore insertion to prevent unintended startup or arcing during connector engagement. The module is placed in position, inserted slowly and evenly until fully seated, then secured with the four screws. Only after mechanical fastening and full seating is confirmed should the ready switch be rotated to theONstate to allow the system to recognize and bring the module online. This matches statement④.

Smart cooling temperature and humidity control is based on where the control “reference point” is measured and regulated.Supply air controluses the unit outlet sensor as the main reference, so the system directly regulates the temperature (and humidity when configured) of the air delivered to the IT area. This provides stable supply conditions and is widely used for predictable airflow organization.Return air controluses the unit inlet/return sensor as the reference, reflecting the heat absorbed from IT loads; it helps the unit respond to real load changes and maintain stable operation when room mixing or load distribution varies.Cold aisle controluses sensors placed in the cold aisle (near rack inlets) as the reference, aligning control with the most critical point for IT reliability—server intake conditions—especially in contained aisle scenarios.Hot aisleis generally not used as a primary temperature-and-humidity control mode because hot aisle conditions are intentionally high and variable (driven by load and containment), and controlling to hot aisle targets can conflict with ensuring stable rack inlet temperature and proper dehumidification behavior. Therefore, A, B, and C are valid control modes.

Compressor preheating is a protection mechanism used during first power-on (and after long power-off periods) to improve compressor reliability before allowing refrigeration startup. The preheating function warms the compressor oil and reduces refrigerant migration and oil dilution, which otherwise can lead to liquid refrigerant in the compressor crankcase. If the compressor starts when oil is diluted or when liquid refrigerant is present, it increases the risk of abnormal noise, poor lubrication, high mechanical stress, and even liquid strike, which can damage the compressor and shorten service life. For data center cooling equipment, where continuous reliability is essential, the commissioning logic treats preheating as a required prerequisite for safe compressor operation. Therefore, O&M practice does not recommend bypassing or manually shutting down compressor preheating just to accelerate commissioning. The correct approach is to keep the unit energized and allow the preheating period to complete, then proceed with commissioning steps (fans, cooling system tests, alarms, and control verification) under proper protection conditions.

Routine UPS maintenance is preventive by design, so it must cover bothenvironmental conditionsandequipment operating status, not only alarms. The equipment room environment directly affects UPS reliability: high temperature accelerates capacitor aging, reduces battery/rectifier reliability, and may trigger derating; improper humidity increases the risk of condensation or electrostatic discharge; dust and poor housekeeping raise the risk of blocked airflow and overheating. Therefore, theenvironment checkin option A is a standard routine item. Option B is also essential because O&M personnel must confirm the UPS is innormal operating mode, verify no hidden alarms exist in the event log, and ensure the load level is within the recommended range to maintain redundancy and efficiency. Option C is true because fans are typical “wear-out” components; abnormal noise or speed changes often appear before a failure and can be detected early through inspection. Option D is false: absence of a front-panel alarm never replaces onsite environmental inspection and basic preventive checks.

In Huawei room air conditioner and precision cooling unit O&M, fan replacement is treated as a maintenance activity that must be recorded in the controller so lifecycle management remains accurate. The controller tracksaccumulated runtimefor wear components such as indoor fans to support preventive maintenance planning, alarm thresholds, and performance analysis. After a fan is replaced, the old runtime value must be cleared so the system can correctly measure the new fan’s service hours, avoiding premature “maintenance due” prompts or misleading reliability assessments. This function belongs to themaintenancefunction set rather than alarm viewing, parameter settings, or basic running status. Therefore, the correct navigation is throughMenu > Maint > Performance Maintenance, where the technician can locate the indoor fan runtime item and reset/clear it after confirming the replacement. Performing this step ensures consistent O&M records, supports correct maintenance intervals, and helps troubleshooting by aligning future fan-related alarms with the actual operating hours of the newly installed component.

In Huawei precision cooling commissioning, the wizard groups functional commissioning items so technicians can validate key subsystems efficiently. Thecooling system commissioningis mandatory because it verifies the primary control and protection loop that directly determines whether the unit can safely provide cooling capacity. This includes confirming the refrigeration or chilled-water cooling path can start and stop correctly, sensors and control logic are valid, and protection conditions (such as abnormal pressures/temperatures, flow conditions, or interlocks) behave as expected. Without completing cooling-system commissioning, the unit’s core purpose—stable temperature control for IT loads—cannot be assured, and the controller cannot reliably judge normal versus fault states during operation.

Other items (indoor fans, condensate pump, humidifier) are important butscenario-dependent: some sites do not use humidification, some drainage designs do not require an internal condensate pump, and fan checks can be handled as part of broader functional tests or may vary by redundancy configuration. Therefore, the wizard allows non-mandatory items to be deselected, but the cooling system commissioning must remain selected to complete a valid baseline commissioning workflow.

In Huawei data center facility equipment (such as precision cooling units and related controllers), alarm presentation follows a clear severity-based design so technicians can recognize urgency immediately without entering detailed menus. Acritical alarmrepresents the highest severity level and is treated as a condition that may impact safe operation, cooling continuity, or equipment protection. For this reason, the LCD controller uses the most prominent visual and audible indications: theindicator turns redto show critical severity, and thebuzzer sounds continuouslyto ensure the alarm cannot be overlooked in a noisy equipment-room environment. This behavior supports rapid response: O&M personnel can quickly identify that immediate action is required, then open the alarm list to locate the root cause, confirm whether the unit has derated or stopped, and execute the prescribed troubleshooting steps (for example, checking power status, sensor readings, fan/compressor status, water flow/pressure, and protection interlocks). Therefore, the statement correctly describes the standard critical-alarm indication method on the LCD controller.

In Huawei NetEco access design, the Web client is reached usingHTTPSto protect credentials and management data in transit. During initial deployment and commissioning, engineers access the NetEco login page by entering the server IP address followed by thedefault HTTPS service port. Huawei’s standard login method specifies that users open a browser and enter server IP:31943to access the NetEco login interface. This port is therefore treated as the default Web login port in typical on-premises NetEco deployments, and it is the baseline value referenced in installation and login guidance. Other ports may appear in specific tools, customized scenarios, version variants, reverse-proxy deployments, or when security policy requires port changes, but those are exceptions driven by planning or product packaging. For exam and commissioning purposes, the correct default login port is the one used by the NetEco Web client entry point under the standard deployment model:31943.

In Huawei delivery scenarios, apreinstalled servermeans the target software (for example, the NetEco platform and its required runtime components) has already been deployed and integrated on the server image before it is handed over for on-site commissioning. Because the installation media has already been applied, the on-site engineer’s work typically shifts from “software installation” to “environment verification and initialization,” such as confirming OS/service status, checking resource allocation, validating database and middleware health, verifying network planning (IP, gateway, DNS/NTP as required), and completing application-level initialization (site creation, user/role configuration, northbound interface settings, and device/model import if needed). In this case,downloading the full installation package is not a mandatory stepfor commissioning, because the package is mainly required when performing a fresh installation or reinstall/upgrade. However, standard practice is still to prepare supporting materials (patches, licenses, and compatibility documents) and ensure the preinstalled version matches the project baseline before acceptance.

For FusionCol8000-C chilled-water systems, Huawei commissioning requires awater leakage/pressure-holding teston the chilled-water piping after installation to verify joint sealing, valve interfaces, and connection integrity before long-term operation. The specified method is toraise the water pressure in the chilled-water pipe to 0.8 MPa, then observe for30 minutesto confirm there is no visible leakage. If the system remains dry, the same pressure isretained for 24 hoursas a stability verification step. The acceptance criterion is that thepressure drop is less than 0.01 MPaover the 24-hour period and no leakage is found, which demonstrates that the piping and fittings meet tightness requirements under the prescribed test pressure. This procedure helps prevent future failures such as slow seepage, corrosion around joints, insulation waterlogging, and unexpected shutdowns caused by water loss or low differential pressure alarms. It also ensures that subsequent flushing, venting, and operational commissioning can be performed safely and reliably.

Huawei room-level air conditioning products are commonly identified by the series name plus a model suffix that indicates the cooling medium and airflow form factor. Anin-room chilled waterunit uses a chilled-water coil as the primary heat-exchange component and relies on the building’s chilled-water system (chiller/plant) rather than an onboard refrigeration compressor for cooling generation. “Horizontal air supply” describes the discharge direction: the unit supplies conditioned air laterally into the room or into a specific airflow organization (such as cold-aisle delivery), supporting predictable airflow paths and stable return air conditions. Within the provided options,FusionCol5000-A050His the model that matches both identifiers: it belongs to Huawei’s room cooling product line and the model code indicates an in-room configuration withchilled-watercapability andhorizontalair supply orientation. The other options belong to different series or represent configurations typically associated with other deployment forms (such as different placement, airflow direction, or system architecture). Therefore, the correct selection isFusionCol5000-A050H.

Huawei’s scenario-based data center facility portfolio is organized around clearly defined solution families that map to typical deployment scenarios and site sizes. FusionModule500 and FusionModule2000 are smart modular data center solutions designed for standardized, fast deployment in equipment rooms and enterprise edge/branch scenarios.They integrate key subsystems such as power supply and distribution, cooling, monitoring, and optional fire protection into a modular architecture that reduces footprint and accelerates on-site delivery. Likewise, FusionDC1000 is Huawei’s prefabricated modular data center series, delivered as complete, factory-integrated modules that combine civil engineering elements with electromechanical infrastructure for rapid construction, predictable quality, and scalable expansion across different capacity tiers. In contrast, FusionDC800 is not used as a defined scenario-based solution name within Huawei’s mainstream data center facility solution lineup (where “FusionDC” offerings are represented by the FusionDC1000 series and “FusionModule” offerings by numbered FusionModule solutions). Therefore, FusionDC800 is the option that does not match Huawei’s scenario-based solution naming.

After ECO mode is enabled on the UPS5000-H, the system’s control objective changes from “always supply the load through the inverter” to “maximize efficiency while keeping protection mechanisms ready.” When themains input is within the configured ECO acceptance window(voltage, frequency, THD, and other quality thresholds), the UPS supplies the critical load primarily through thestatic bypass path, which has lower conversion losses than continuous double-conversion. The inverter remains synchronized and on standby, so if the mains quality deteriorates or an abnormal condition is detected, the UPS canrapidly transferthe load back to inverter operation to maintain output stability. Battery mode is only used when the rectifier/bypass source is unavailable or out of range, and maintenance bypass is a manual service path used for isolation during maintenance, not for normal energy-saving operation. Therefore, with stable utility power and ECO configured, the UPS5000-H mainly operates instatic bypass mode.