HCIP-5G-RNP&RNO Questions and Answers
Which message is used to provide the LTE frequencies and reselection parameters configured on the 5G side?
Options:
SIB6
SIB5
SIB4
SIB3
Answer:
BExplanation:
System Information Block 5 (SIB5) is the correct answer because it provides information required for inter-Radio Access Technology (inter-RAT) cell reselection from 5G NR to LTE E-UTRA.
When an NR UE operates in RRC_IDLE or RRC_INACTIVE, cell reselection allows it to identify and camp on a more appropriate serving cell according to broadcast network priorities and radio conditions.
The NR network broadcasts the relevant E-UTRA reselection configuration through SIB5.
According to 3GPP TS 38.331, SIB5 contains the carrierFreqListEUTRA information element, identifying LTE carrier frequencies that the UE may evaluate.
It also contains t-ReselectionEUTRA , which determines the applicable inter-RAT reselection timing requirement.
Additional information can include frequency priorities, reselection thresholds, minimum received signal-level requirements, and neighboring-cell restrictions.
These parameters allow the UE to compare candidate LTE cells against the NR serving cell and apply the configured reselection criteria.
The remaining options serve different functions.
SIB3 provides NR intra-frequency cell-reselection information.
SIB4 provides NR inter-frequency cell-reselection information.
SIB6 is not the system information block used to advertise the NR-to-E-UTRA reselection frequency configuration.
Therefore, SIB5 is specifically responsible for supplying the LTE frequencies and associated reselection parameters configured by the NR network.
Official Reference: 3GPP TS 38.331, Section 6.3.1, SIB5 Information Element ; TS 38.304, UE Procedures in Idle Mode and RRC_INACTIVE .
Which of the following MCS indices is required for 256QAM scheduling in downlink peak-rate testing?
Options:
MCS index 32
MCS index 27
MCS index 28
MCS index 23
Answer:
BExplanation:
MCS index 27 is the expected answer because it represents the highest non-reserved spectral-efficiency entry in the conventional NR PDSCH MCS table supporting 256QAM.
The Modulation and Coding Scheme (MCS) determines the modulation order and target coding rate used for scheduled data transmission.
For 256QAM, the modulation order is Q_m=8, meaning eight coded bits are mapped to each modulation symbol.
According to 3GPP TS 38.214, Table 5.1.3.1-2, MCS index 27 uses modulation order 8 and a target coding-rate parameter of 948/1024.
Its spectral efficiency is approximately 7.4063 bits per resource element before applicable resource overheads.
This makes index 27 particularly relevant when evaluating maximum downlink throughput under favorable radio conditions.
However, an important distinction exists between enabling 256QAM and achieving maximum spectral efficiency.
MCS index 23 also uses 256QAM, with a target coding-rate parameter of 797/1024 and a lower spectral efficiency of approximately 6.2266.
Therefore, both indices 23 and 27 can represent 256QAM modulation, but index 27 provides the higher nominal spectral efficiency.
MCS index 28 is reserved in the referenced table, while index 32 is outside the five-bit MCS index range.
Consequently, B is correct for maximum peak-rate testing.
Official Reference: 3GPP TS 38.214, Section 5.1.3.1, Table 5.1.3.1-2, MCS Index Table 2 for PDSCH .
Technical warning / qualification: Option D also represents 256QAM. The question is unambiguous only if peak-rate testing means selecting the highest non-reserved spectral-efficiency entry. The wording should explicitly state this condition.
In NSA networking, which of the following counters measure the number of abnormal SgNB releases caused by their respective causes?
Select All that Apply
Options:
N.NsaDc.SgNB.Rel.Coverage
N.NsaDc.SgNB.AbnormRel.Radio.UeLost
N.NsaDc.SgNB.AbnormRel.NoReply
N.NsaDc.SgNB.AbnormRel.Trans
Answer:
B, C, DExplanation:
Options B, C, and D are the intended answers because their counter names explicitly identify abnormal Secondary gNodeB (SgNB) release events and distinguish the associated failure causes.
In Non-Standalone (NSA) E-UTRA–NR Dual Connectivity, the SgNB provides NR secondary connectivity while the LTE eNodeB maintains the master connection.
Abnormal SgNB releases can occur because of radio-link failures, UE communication failures, transmission-network faults, or unsuccessful signaling procedures.
Option B — N.NsaDc.SgNB.AbnormRel.Radio.UeLost identifies abnormal release events associated with loss of UE communication at the radio layer.
This counter is relevant when investigating coverage deterioration, radio-link instability, or unexpected UE disappearance from the secondary connection.
Option C — N.NsaDc.SgNB.AbnormRel.NoReply identifies abnormal releases associated with missing expected responses during applicable procedures.
Option D — N.NsaDc.SgNB.AbnormRel.Trans identifies abnormal releases attributable to transmission-layer problems, such as faults affecting transport connectivity or associated signaling paths.
Option A — N.NsaDc.SgNB.Rel.Coverage identifies coverage-related SgNB releases, but its name does not classify those events as abnormal releases.
The key distinction is between general release counters and counters explicitly classified under abnormal-release causes.
Therefore, B, C, and D are the intended selections.
Official Reference: 3GPP TS 37.340, E-UTRA and NR Multi-Connectivity , Secondary Node Release procedures; TS 28.552, 5G Performance Measurements .
Technical warning / qualification: The precise N.NsaDc counter names are Huawei-specific. Their interpretations are consistent with the updated question bank, but the official Huawei performance-counter dictionary has not been supplied or independently verified. The 3GPP references establish the procedure, not these exact counter definitions.
Notification Control is used exclusively for GBR QoS flows and is an optional parameter.
Options:
True
False
Answer:
AExplanation:
The statement is true because Notification Control is an optional Quality of Service (QoS) parameter applicable to Guaranteed Bit Rate (GBR) QoS flows in the 5G system architecture.
In 5G, QoS flows enable differentiated treatment of traffic according to service requirements such as guaranteed throughput, packet delay, reliability, and priority.
GBR QoS flows are characterized by Guaranteed Flow Bit Rate (GFBR) and Maximum Flow Bit Rate (MFBR) parameters.
Notification Control allows the NG-RAN to report when the guaranteed QoS requirements associated with a GBR QoS flow can no longer be satisfied.
According to 3GPP TS 23.501, the Session Management Function (SMF) enables Notification Control when the corresponding QoS Notification Control parameter is present in the Policy and Charging Control (PCC) rule received from the Policy Control Function (PCF).
The parameter is subsequently communicated to the NG-RAN as part of the QoS profile.
When Notification Control is active, the NG-RAN monitors whether the required GFBR, Packet Delay Budget (PDB), and Packet Error Rate (PER) conditions remain achievable.
If these requirements cannot be fulfilled, the NG-RAN sends the appropriate notification toward the SMF.
Notification Control is not mandatory for every GBR QoS flow and is not a standard parameter applied to ordinary non-GBR flows.
Therefore, option A is correct.
Official Reference: 3GPP TS 23.501, Section 5.7.2.4, Notification Control .
For both the VoNR and EPS fallback solutions, the 5GC must interwork with the IMS.
Options:
True
False
Answer:
AExplanation:
The statement is true because both Voice over New Radio (VoNR) and Evolved Packet System (EPS) fallback provide voice services through the IP Multimedia Subsystem (IMS), although the radio-access and core-network procedures used to deliver the voice session differ.
In a VoNR deployment, the UE maintains its connection to the 5G Core (5GC) through NR. IMS signaling and media traffic are transported over an appropriate PDU session, with the 5GC supporting QoS-flow establishment, policy enforcement, and connectivity to the IMS network.
The Session Management Function (SMF) manages the corresponding PDU session, while the User Plane Function (UPF) provides user-plane connectivity toward the IMS data network.
EPS fallback applies when the 5G system cannot provide the required IMS voice service directly over its existing radio access.
In this case, the 5GC and NG-RAN coordinate a handover or redirection toward LTE connected to the EPC. IMS voice establishment or continuation then takes place over the EPS.
Importantly, EPS fallback does not mean that the voice-media path remains anchored in the 5GC after fallback. It means that the 5G system participates in IMS voice-service support and coordinates access to EPS when necessary.
Official Reference: 3GPP TS 23.501, Sections 5.16.3.1–5.16.3.10, IMS Support and IMS Voice Service via EPS Fallback .
Which of the following channels or signals support closed-loop power control?
Select All that Apply
Options:
PUSCH
PRACH
PBCH
PUCCH
Answer:
A, DExplanation:
The Physical Uplink Shared Channel (PUSCH) and Physical Uplink Control Channel (PUCCH) support closed-loop transmit-power control in 5G NR.
Closed-loop power control enables the gNodeB to adjust UE transmission power dynamically according to radio-channel conditions, received signal quality, and interference-management requirements.
Option A — PUSCH: The PUSCH carries uplink user data and selected control information. Its transmit-power calculation combines configured open-loop parameters with closed-loop power adjustments communicated through Transmit Power Control (TPC) commands.
These adjustments help maintain reliable uplink reception while limiting unnecessary UE power consumption and inter-cell interference.
Option D — PUCCH: The PUCCH carries uplink control information, including HARQ acknowledgments, scheduling requests, and CSI reports. Its power-control procedure also incorporates TPC commands and the corresponding closed-loop adjustment state.
Option B — PRACH: PRACH uses a random-access transmit-power calculation and power-ramping mechanism. It does not use the conventional PUSCH/PUCCH closed-loop TPC procedure.
Option C — PBCH: PBCH is a downlink broadcast channel transmitted by the gNodeB, so UE uplink closed-loop power control does not apply.
Therefore, PUSCH and PUCCH are the correct selections.
Official Reference: 3GPP TS 38.213, Sections 7.1.1 and 7.2.1, PUSCH and PUCCH Transmit Power Control ; TS 38.321, Random Access Procedure .
Which of the following timers is specific to 5G networks?
Options:
T311
T310
T300
T319
Answer:
DExplanation:
T319 is the correct answer because it is defined in the 5G New Radio (NR) Radio Resource Control (RRC) specification to supervise the RRC connection resume procedure.
5G NR supports three principal RRC states: RRC_IDLE, RRC_CONNECTED, and RRC_INACTIVE. The RRC_INACTIVE state allows a UE to retain its Access Stratum (AS) context while reducing signaling overhead and power consumption.
When a UE in RRC_INACTIVE needs to resume communication, it initiates the RRC connection resume procedure by transmitting an RRCResumeRequest or RRCResumeRequest1 message. Timer T319 supervises this procedure.
If the UE receives an appropriate RRCResume message, T319 is stopped, and the UE restores the relevant radio-bearer configuration and transitions to RRC_CONNECTED.
If T319 expires before successful completion, the UE performs RRC resume failure handling and enters RRC_IDLE.
The remaining timers are also present in LTE:
T300: Supervises RRC connection establishment.
T310: Supports radio-link failure detection.
T311: Supervises cell selection during RRC connection reestablishment.
Therefore, among the listed options, T319 is specifically associated with the NR RRC connection resume procedure.
Official Reference: 3GPP TS 38.331, Sections 5.3.13.3–5.3.13.5, RRC Connection Resume , and Section 7.1.1, RRC Timers .
For NR coverage optimization, the principle is to preferentially optimize SS-SINR and then SS-RSRP.
Options:
True
False
Answer:
BExplanation:
Synchronization Signal Reference Signal Received Power (SS-RSRP) measures the received power of the synchronization-signal reference elements and is a fundamental indicator of NR radio coverage.
SS-RSRP optimization establishes whether the received serving-cell signal is sufficiently strong throughout the required coverage area.
Typical corrective actions include adjusting antenna azimuth, electrical downtilt, antenna height, reference-signal transmission characteristics, and site configuration.
Once acceptable signal-strength coverage has been established, the optimization process evaluates signal quality.
Synchronization Signal Signal-to-Interference-plus-Noise Ratio (SS-SINR) measures the synchronization-signal power relative to interference and noise.
Poor SS-SINR can occur even when SS-RSRP is strong, particularly in areas affected by overlapping cell coverage, excessive interference, or unsuitable beam configurations.
Interference coordination, antenna-pattern optimization, and mobility-parameter adjustments may improve SS-SINR and subsequent service performance.
The two measurements must ultimately be considered together because strong signal power does not guarantee acceptable radio quality.
However, the statement reverses the intended priority by placing SS-SINR before SS-RSRP.
Therefore, option B is correct.
Official Reference: 3GPP TS 38.215, Physical Layer Measurements ; TS 28.100, Annex A.1.3, Coverage Optimization Requirements and Measurements .
Technical warning / qualification: The sequence is a planning and optimization guideline, not an absolute 3GPP-mandated workflow. In an interference-limited network, SS-SINR may require immediate attention even when SS-RSRP is adequate.
In an NSA access issue, which of the following can cause a UE not to report B1 measurement results?
Select All that Apply
Options:
When the base station is close to the UE, the downlink power is oversaturated. As a result, the UE fails to detect cells.
The NR frequency configured on the LTE side is not the NR SSB frequency.
The UE measurement result does not meet the B1 threshold.
The NR cell status is abnormal.
Answer:
A, B, C, DExplanation:
All four conditions can prevent a UE from generating or transmitting a valid B1 measurement report during Non-Standalone (NSA) E-UTRA–NR Dual Connectivity (EN-DC) access.
In NSA architecture, the LTE eNodeB acts as the Master Node and configures NR inter-RAT measurements to determine whether an eligible 5G NR cell can be added as a Secondary Node.
Event B1 is triggered when the measured quality of an inter-RAT neighboring cell exceeds the configured threshold, subject to hysteresis and time-to-trigger requirements.
Option A: Excessive received signal power may saturate the UE receiver, degrading synchronization-signal detection and preventing successful NR cell measurements.
Option B: If the LTE-side measurement configuration identifies a frequency that does not correspond to the intended NR SSB carrier, the UE may be unable to detect the target NR synchronization signals.
Option C: If the measured NR signal does not satisfy the configured B1 entry condition, the reporting event is not triggered.
Option D: An abnormal NR cell may fail to transmit the required synchronization signals correctly or provide measurable radio coverage, preventing a valid measurement result.
Therefore, all four conditions are plausible causes of missing B1 measurement reports.
Official Reference: 3GPP TS 36.331, Inter-RAT Measurement Reporting — Event B1 ; TS 38.533, Section 8.4.2, NR Inter-RAT Event-Triggered Reporting Requirements .
Which propagation model is selected by default when the U-Net is used for simulation?
Options:
Answer:
Rayce
Answer:Uma
Answer:Umi
Answer:Rma
Answer:C
Propagation models are fundamental to radio-network planning because they estimate signal attenuation across different deployment environments.
The Urban Microcell (UMi) model represents deployments in which base stations are typically installed below surrounding rooftop levels, often along streets and within dense urban environments.
UMi propagation calculations account for relevant line-of-sight and non-line-of-sight characteristics, including distance-dependent path loss and environmental conditions.
The Urban Macrocell (UMa) model represents larger macrocell deployments, generally involving higher base-station antenna positions and different propagation assumptions.
The Rural Macrocell (RMa) model addresses comparatively open rural environments, where terrain, longer propagation distances, and lower building density influence coverage predictions.
Ray-tracing models use geometrical descriptions of the environment to estimate propagation through mechanisms such as reflection, diffraction, and scattering.
Huawei's official 5G Wireless Network Planning Solution White Paper confirms that its planning solutions support UMi, UMa, and Huawei-developed ray-tracing propagation models.
However, the availability of these models does not establish which model is selected by default in a particular release of Huawei U-Net.
Official Reference: Huawei, 5G Wireless Network Planning Solution White Paper , Sections 2.2.1 and 2.2.3, High-Precision 5G Propagation Model and Refined Coverage Prediction .
Which of the following PUCCH measurement counters is used for outer-loop power control on PUCCH?
Options:
SINR
Power spectrum density
RSRP
BLER
Answer:
DExplanation:
Block Error Rate (BLER) is the intended answer because outer-loop power-control algorithms use error-performance feedback to adjust the target received signal quality required for reliable control-channel reception.
PUCCH carries essential Uplink Control Information (UCI), including HARQ acknowledgments, scheduling requests, and configured channel-state reports.
Errors in these transmissions can produce unnecessary retransmissions, incorrect scheduling decisions, and reduced radio-network efficiency.
The distinction between inner-loop and outer-loop power control is important.
Inner-loop power control adjusts transmission power according to the difference between measured signal quality, commonly expressed through SINR, and a configured target.
The gNodeB can issue Transmit Power Control (TPC) commands to modify the UE's PUCCH transmit power.
Outer-loop power control adjusts the target signal-quality requirement according to observed error performance. When reception reliability deteriorates, the target SINR can be increased to improve decoding probability. Conversely, consistently satisfactory error performance can permit a reduction in the target.
RSRP measures received reference-signal power, while power spectral density expresses signal or noise power per unit bandwidth. Neither directly represents the error-performance feedback used in the intended outer-loop mechanism.
Therefore, BLER is the expected examination answer, with implementation-specific qualifications.
Official Reference: 3GPP TS 38.213, Section 7.2.1, PUCCH Transmit Power Control .
Technical warning / qualification: 3GPP specifies the PUCCH power-control signaling and calculations but does not mandate one universal BLER-based outer-loop algorithm. Huawei implementations may use BER or another error-performance measure depending on the radio technology and PUCCH configuration.
Which of the following channels or signals uses the same transmit power as the PUSCH?
Options:
PRACH
PDSCH
SRC
PUCCH
Answer:
CExplanation:
In NR, SRS is transmitted by the UE to provide uplink channel-sounding information for scheduling, channel estimation, beam management, and MIMO-related procedures.
The SRS transmission-power calculation follows the uplink power-control principles specified in 3GPP TS 38.213.
These principles include configured target-power parameters, transmission bandwidth, estimated path loss, path-loss compensation, and applicable closed-loop adjustments.
Under certain configurations, SRS may share a power-control adjustment state with PUSCH. Under other configurations, separate adjustment states and SRS-specific parameters are used.
Consequently, SRS transmission power is related to the PUSCH power-control mechanism but is not necessarily numerically identical to PUSCH transmit power .
PRACH has its own random-access transmit-power and power-ramping procedures.
PUCCH uses a separate uplink power-control calculation, while PDSCH is a downlink physical channel.
The intended comparison therefore points toward SRS, represented incorrectly as SRC in the original choices.
Official Reference: 3GPP TS 38.213, Sections 7.1 and 7.3, PUSCH and SRS Transmit Power Control .
Technical warning / qualification: Replace option C, SRC , with SRS . The question should also state uses a related power-control mechanism rather than uses the same transmit power , because the latter is not universally correct.
How many narrow beams are transmitted when the 4:1 slot configuration and 30-kHz subcarrier spacing are used, the SSB pattern is case C, and the maximum number of SSBs is 8?
Options:
8
4
7
1
Answer:
AExplanation:
The expected answer is eight narrow beams because the described configuration permits up to eight Synchronization Signal/PBCH Blocks (SSBs) within an applicable SSB burst set.
In 5G NR, beam sweeping enables the gNodeB to transmit synchronization information in different spatial directions, allowing UEs to identify suitable beams during cell search and initial access.
An SSB contains the Primary Synchronization Signal (PSS), Secondary Synchronization Signal (SSS), Physical Broadcast Channel (PBCH), and associated demodulation reference signals.
SSB pattern Case C uses 30 kHz subcarrier spacing and specifies candidate SSB transmission locations within the applicable half-frame.
For a configuration supporting a maximum of eight SSBs, the network can associate eight transmitted SSBs with eight distinct beam directions.
The specified 4:1 TDD slot configuration influences the available downlink transmission occasions, while the SSB pattern defines the candidate synchronization-block positions.
When all eight candidate SSB positions are configured for transmission, the gNodeB can sweep eight narrow beams during the SSB burst set.
However, the maximum supported SSB count and the number actually transmitted are not necessarily identical. The network can configure a smaller active subset.
Therefore, eight is the intended answer under the assumption that all eight SSB positions are enabled.
Official Reference: 3GPP TS 38.213, Section 4.1, Cell Search and SS/PBCH Block Candidate Positions ; TS 38.211, Section 7.4.3, SS/PBCH Block Structure .
Technical warning / qualification: The question specifies a maximum of eight SSBs but does not explicitly state that all eight are transmitted. The correct choice is A under the intended full-beam configuration.
Which of the following physical-layer processing procedures is dedicated to the DFT-S-OFDM waveform?
Options:
Modulation
Scrambling
Layer mapping
Transformer precoding
Answer:
DExplanation:
Transform precoding is the distinguishing physical-layer processing operation associated with Discrete Fourier Transform-spread Orthogonal Frequency Division Multiplexing (DFT-S-OFDM).
In 5G NR, uplink data transmission on the Physical Uplink Shared Channel (PUSCH) can use CP-OFDM or DFT-S-OFDM, subject to the applicable configuration.
DFT-S-OFDM introduces a Discrete Fourier Transform (DFT) operation into the symbol-processing chain before resource mapping and OFDM signal generation. This spreads modulation symbols across the allocated subcarriers.
A principal benefit is the reduction of Peak-to-Average Power Ratio (PAPR) compared with conventional CP-OFDM in typical operating conditions.
Lower PAPR enables the UE power amplifier to operate more efficiently, reducing the required amplifier back-off and potentially improving uplink coverage, particularly for power-limited terminals.
Scrambling, modulation, and layer mapping are not exclusive to DFT-S-OFDM. These operations also occur in other NR physical-layer processing chains.
By contrast, transform precoding provides the characteristic DFT-spreading operation associated with DFT-S-OFDM transmission.
Accordingly, option D is correct because it identifies the processing operation that distinguishes DFT-S-OFDM from conventional CP-OFDM.
Official Reference: 3GPP TS 38.211, Sections 6.3.1.1–6.3.1.4, PUSCH Scrambling, Modulation, Layer Mapping, and Transform Precoding ; TS 38.214, Section 6.1.3.
Technical warning / qualification: The original option states Transformer precoding . The standardized term is Transform precoding . The wording should be corrected in the published question bank.
Only one codeword is needed when four streams are transmitted over the air interface.
Options:
True
False
Answer:
AExplanation:
The statement is true because 5G NR supports mapping a single codeword to as many as four spatial transmission layers in the standard downlink spatial-multiplexing configuration.
A codeword represents a sequence of encoded data bits generated through channel coding and associated processing before modulation and layer mapping.
Spatial layers are logical MIMO transmission streams used to transport data across multiple spatial dimensions of the radio channel.
The number of codewords is not necessarily equal to the number of MIMO layers.
According to 3GPP TS 38.211, the PDSCH codeword-to-layer mapping procedure supports one codeword for transmissions using one, two, three, or four layers.
For example, when four layers are scheduled, modulation symbols from the single codeword are distributed across four layers according to the specified mapping procedure.
When the configured downlink transmission uses five to eight spatial layers, two codewords are supported, with the corresponding layer allocation determined by the applicable mapping table.
This distinction is essential when evaluating MIMO transmission rank, transport-block processing, HARQ operation, and channel-coding requirements.
Consequently, a four-layer spatial-multiplexing transmission requires only one codeword under the standardized NR mapping configuration.
Official Reference: 3GPP TS 38.211, Section 7.3.1.3, Table 7.3.1.3-1, Codeword-to-Layer Mapping for Spatial Multiplexing .
Which TA offsets may be configured for a 5G network operating in n41?
Select All that Apply
Options:
0
25600tc
39936Tc
51200Tc
Answer:
B, CExplanation:
Options B and C are correct because the standardized Timing Advance (TA) offset values applicable to an NR Frequency Range 1 (FR1) Time Division Duplex (TDD) deployment include 25600 T_c and 39936 T_c, depending on the coexistence scenario.
NR band n41 operates in FR1 using TDD.
Timing Advance enables the UE to adjust uplink transmission timing so that signals from different UEs arrive at the gNodeB within the required timing alignment.
In NR, the effective uplink timing relationship includes a timing-advance offset represented by N_TA,offset.
According to the standardized timing requirements:
Option B — 25600 T_c: This value applies to FR1 TDD operation without the relevant LTE–NR coexistence requirements. It is also the default FR1 offset in applicable configurations when no explicit n-TimingAdvanceOffset is provided.
Option C — 39936 T_c: This value applies to FR1 TDD operation involving LTE–NR coexistence.
Option A — 0 T_c: This value is associated with the specified FR1 FDD coexistence case, not the normal n41 TDD configurations represented by this question.
Option D — 51200 T_c: This is not one of the applicable standardized NR timing-advance offset values.
Therefore, B and C are correct.
Official Reference: 3GPP TS 38.533, Section 4.4.1.0.1, Table 4.4.1.0.1-2, Timing Advance Offset Values ; TS 38.213, Section 4.2, Transmission Timing Adjustments .
When multiple slices exist in the 5GC, which of the following modules is responsible for selecting a slice?
Options:
AMF
NSSF
NRF
NEF
Answer:
BExplanation:
The Network Slice Selection Function (NSSF) is the dedicated 5G Core network function responsible for supporting network-slice selection.
Network slicing enables operators to create multiple logical networks on common infrastructure, allowing differentiated service capabilities for enhanced Mobile Broadband (eMBB), Ultra-Reliable Low-Latency Communications (URLLC), and massive Machine-Type Communications (mMTC).
Each network slice is identified using Single Network Slice Selection Assistance Information (S-NSSAI), consisting of a Slice/Service Type (SST) and an optional Slice Differentiator (SD).
During UE registration, the Access and Mobility Management Function (AMF) processes the requested slice information and may interact with the NSSF through the Nnssf service-based interface.
The NSSF assists with determining the Allowed NSSAI, identifying suitable network-slice instances, and determining appropriate AMF sets for the requested slices.
The remaining network functions have distinct responsibilities.
AMF manages UE registration, access authorization coordination, and mobility management. Although it participates in slice-selection procedures, it is not the dedicated slice-selection function.
NRF provides network-function registration and discovery services.
NEF securely exposes network capabilities and events to authorized external applications.
Therefore, NSSF is the correct answer because network-slice selection is explicitly included in its standardized functional responsibilities.
Official Reference: 3GPP TS 23.501, Sections 5.15 and 6.2.14, Network Slicing and NSSF Functionality .
Which of the following cannot be transmitted on the PDCCH?
Options:
PDSCH resource indication
PDSCH modulation
PUSCH resource indication
PMI
Answer:
DExplanation:
The Precoding Matrix Indicator (PMI) is the correct answer because PMI is primarily reported by the UE as part of Channel State Information (CSI), rather than being transmitted as a conventional Downlink Control Information (DCI) field on the Physical Downlink Control Channel (PDCCH).
In 5G NR, the PDCCH carries scheduling and control information from the gNodeB to the UE. DCI formats determine whether the signaling concerns uplink transmission, downlink transmission, or another supported control procedure.
For downlink scheduling, DCI formats 1_0 and 1_1 can specify PDSCH resource assignments, including frequency-domain and time-domain resource allocation.
The DCI also contains a Modulation and Coding Scheme (MCS) field. This identifies the modulation order and target coding rate associated with the scheduled PDSCH transmission.
For uplink scheduling, DCI formats 0_0 and 0_1 can provide PUSCH resource allocations and associated transmission parameters.
PMI serves a different purpose. Based on configured CSI-RS measurements, the UE determines a preferred precoding matrix and reports the associated PMI to the gNodeB.
This feedback is conveyed through applicable uplink reporting procedures using PUCCH or PUSCH.
Therefore, PMI is the only listed parameter that is not ordinarily carried as a PDCCH DCI field.
Official Reference: 3GPP TS 38.212, Section 7.3.1, DCI Formats ; TS 38.214, Section 5.2, Channel State Information Reporting .