Black Friday Flash Sale - Everything Must Go at 75% Off - Ends in 0d 00h 00m 00s - Coupon code: w75best

Netapp NS0-094 Dumps

Page: 1 / 8
Total 81 questions

NetApp Hardware Support Engineer Professional Exam Questions and Answers

Question 1

Which type of AutoSupport message would you expect to see triggered automatically when ONTAP software detects a NetApp WAFL inconsistency on an aggregate?

Options:

A.

MEDIUM ERROR DURING RECONSTRUCTION

B.

CHECKSUM ERROR

C.

WAFL INCONSISTENT USER DATA BLOCK

D.

WAFL INCONSISTENT BLOCK

Question 2

You have a NetApp ONTAP cluster that is serving both SMB over 10Gbe and FC data. An application owner has started to complain about poor performance and asks you to research the issue. When looking through EMS messages, you see the following output:

as

Which defective component triggers the EMS message?

Options:

A.

10Gbe module

B.

fiber cable

C.

32G FC module

D.

adapter card in slot 2

Question 3

In the latest MANAGEMENT LOG AutoSupport message, you try to inspect the ENVIRONMENT section but find it empty.

In which section of AutoSupport can you find the reason?

Options:

A.

AUTOSUPPORT-BUDGET.XML

B.

HEADERS

C.

AUTOSUPPORT-HISTORY.XML

D.

MANIFEST.XML

Question 4

You notice the following system alert during a routine check of a four-node NetApp ONTAP cluster:

Alert ID: SwitchIfDead_Alert

Resource: Slot: 0 Port: 55 100G - Level

Severity: Major

Probable Cause:

The interface broadcomswitch-011/Slot: 0

Port: 55 100G - Level is up, but it is

not passing unicast traffic.

Possible Effect:

The lack of transmit or receive traffic

reported by the switch can indicate

issues with port-level or switch-level

data packet forwarding.

Corrective Actions:

1) Check interface counters and neighbor

discovery information to verify the

port's activity.

2) Check cluster and switch health status.

The customer confirms that the cables are connected correctly and interface LEDs on the switches are on.

What is the next step in troubleshooting this issue?

Options:

A.

Remove the cluster ports from the cluster IPspace and cluster broadcast domain, and delete the health alerts.

B.

Verify the configuration of the switchports with the output of RCF Configurator.

C.

Bounce the cluster interconnect ports on the ONTAP cluster nodes that are reporting this alert.

D.

Revert the ONTAP software upgrade to see if the alert disappears.

Question 5

You need to upgrade your cluster switches to a new version of firmware.

Which command do you use to prevent automatic case creation?

Options:

A.

system node autosupport invoke -node * -type all -message STOP=5h

B.

system node autosupport invoke -node * -type all -message IGNORE=5h

C.

system node autosupport invoke -node * -type all -message MAINT=5h

D.

system node autosupport invoke -node * -type all -message SUPPRESS=5h

Question 6

A 4-node NetApp ONTAP cluster sent an alert that one of the cluster interconnect switches has failed. After replacement, the system administrator notices that half of the cluster LIFs are not on their home ports.

Which parameter must the system administrator enable to automatically migrate the cluster LIFs?

Options:

A.

failover-policy

B.

auto-revert

C.

allow-lb-migrate

D.

home-port

Question 7

Where is a kernel core file stored on a FAS9000 system that is running ONTAP 9.12.1 software?

Options:

A.

on the partner root aggregate

B.

on the root aggregate

C.

on the mailbox disk

D.

on the boot device

Question 8

A node has unexpectedly failed and is unresponsive through its node management interface.

Which two commands from the Service Processor are helpful to determine the root cause? (Choose two.)

Options:

A.

sp status –d

B.

event log show

C.

system log

D.

system core

Question 9

What are two options to remove Failure Byte on disks that are marked as failed? (Choose two.)

Options:

A.

Power cycle the disk shelf.

B.

Reseat the disk.

C.

Update the disk firmware.

D.

Unfail the disk

Question 10

You are troubleshooting an L2 connectivity problem, and you want to analyze network traffic.

Which command do you use to capture network packets?

Options:

A.

traceroute

B.

netstat

C.

ping

D.

tcpdump

Question 11

Which two of the following are field replaceable units (FRUs) on an AFF A220 system? (Choose two.)

Options:

A.

NVMEM battery

B.

mSATA boot device

C.

NVME Flash Cache feature

D.

chassis fan

Question 12

What are two valid options for uploading a core file from a node that is running ONTAP 9.12.1 software to NetApp for analysis? (Choose two.)

Options:

A.

system node autosupport invoke -diagnostic

B.

Download via CIFS and upload to upload.netapp.com.

C.

Download via Service Processor Infrastructure (SPI) and upload to upload.netapp.com.

D.

system node autosupport invoke-core-upload

Question 13

What happens when the command diskcopy is run from nodeshell?

Options:

A.

It pre-fails a drive in an aggregate and copies it to a spare.

B.

It performs a low-level copy of the disk to another disk.

C.

It copies the disk content to a specified volume.

D.

It triggers a RAID reconstruction of that disk.

Question 14

While performing a health check on a cluster, you notice the following entries in the cluster event log:

as

Referring to the exhibit, which of the following actions do you take?

Options:

A.

Sanitize the disk.

B.

Reseat the disk.

C.

Review the current firmware and known issues.

D.

Use diskcopy to copy the disk to a working spare.

Question 15

Which command can you use to confirm successful completion of an ONTAP upgrade?

Options:

A.

system controller sp upgrade show

B.

cluster image show-update-progress

C.

job show –jobtype upgrade

D.

system node upgrade-revert upgrade-task –node < nodename > –version < ontap Version >

Question 16

Which type of core file is generated when a node panics?

Options:

A.

mgwd core

B.

user space core

C.

sync core

D.

kernel core

Question 17

Which two tools can you use to invoke AutoSupport? (Choose two.)

Options:

A.

NetApp Cloud Insights

B.

CLI

C.

the NetApp Active IQ website

D.

the SmartSolve tool

Question 18

What is the default amount of time that a volume is available for recovery from the volume recovery queue following a volume deletion?

Options:

A.

12 hours

B.

48 hours

C.

72 hours

D.

24 hours

Question 19

While reviewing a fresh install of a new NetApp ONTAP HA pair, the Field Support engineer notices that the controllers do not report the same system storage configuration.

The first controller reports the following:

System Storage Configuration: Multi-Path HA

The second controller reports the following:

System Storage Configuration: Single-Path HA

There are no EMS errors, and there are no alerts on the system or on NetApp ONTAP System Manager.

What is the next step in troubleshooting this issue?

Options:

A.

Ensure that the second controller is set up for ADP.

B.

Ensure that all disk shelves are connected, with at least four SAS cables to each controller.

C.

Reboot the controller that is reporting the single-path configuration.

D.

Check cabling to the controller that is reporting the single-path configuration.

Question 20

Which RAID type provides protection against three disk failures?

Options:

A.

RAID DP

B.

RAID-TEC

C.

RAID 5

D.

RAID 4

Question 21

When you plan an ONTAP upgrade, which NetApp tool generates a detailed upgrade plan?

Options:

A.

ONTAP System Manager

B.

Active IQ Unified Manager

C.

Upgrade Advisor

D.

Active IQ Config Avisor

Question 22

After a panic, the customer asks you to explain the error “watchdog timeout.”

Which explanation would be appropriate?

Options:

A.

An optional software that monitors system performance.

An overloaded system fails to reset the watchdog and watchdog induces a system panic.

B.

An optional component included with Active IQ Unified Manager.

It notifies a user if watchdog fails to reach the storage system within a certain period.

C.

A service that detects and recovers from computer malfunctions.

A hardware or software error prevents update of watchdog and it induces a system panic.

D.

A service that monitors network activity and protects data.

A watchdog induces system panic to protect data if malicious activity is detected.

Question 23

In a SAS stack of shelves, what is the topology of the connection between expander and disk?

Options:

A.

arbritrated loop

B.

point-to-point

C.

loop

D.

ring

Question 24

When you add a new disk to an ONTAP 9.1 system, you see an error that the disk “has raid label with version (16), which is not within the currently supported range (14-15).” What is one possible cause of this error?

Options:

A.

The disk is a non-zeroed spare.

B.

The disk firmware is too new for ONTAP software.

C.

The disk needs to be assigned to the new system.

D.

The disk was in a system with a newer version of ONTAP software

Page: 1 / 8
Total 81 questions